:::

3-3 DTH22 溫溼度感應器

    DHT22為相當優秀溫度、濕度的感測器,很多智慧家電皆有它的蹤跡,價格還算便宜...

    連接DHT22需在其第1、2腳位,串接一電阻(1k OM),第1腳接5v,第2腳接 Arduino Digital 7,第4腳接地

需要材料:

    DHT22 溫濕度傳感器 * 1

    10k OM 電阻 * 1

    麵包板跳線 橘色 * 1

    麵包板跳線 紅色 * 1 (需修剪長度)

    DHT22的程式庫需另外下載,請在Arduino IDE程式的[草稿碼]→[匯入程式庫]→[管理程式庫...]

搜尋DHT22,[選擇版本] 點選最新版本,按 [安裝]

測試程式:

    [檔案]→[範例]→[DHT sensor library]→[DHTtester]

 

修改程式:

#define DHTPIN 7 // 研習使用Arduino Digital 7,請修改為7

 

程式庫提供的範例 DHTtester

// Example testing sketch for various DHT humidity/temperature sensors
// Written by ladyada, public domain

#include "DHT.h"

#define DHTPIN 7     // 研習使用Arduino Digital 7,請修改為7

// Uncomment whatever type you're using!
//#define DHTTYPE DHT11   // DHT 11
#define DHTTYPE DHT22   // DHT 22  (AM2302), AM2321
//#define DHTTYPE DHT21   // DHT 21 (AM2301)

// Connect pin 1 (on the left) of the sensor to +5V
// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1
// to 3.3V instead of 5V!
// Connect pin 2 of the sensor to whatever your DHTPIN is
// Connect pin 4 (on the right) of the sensor to GROUND
// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor

// Initialize DHT sensor.
// Note that older versions of this library took an optional third parameter to
// tweak the timings for faster processors.  This parameter is no longer needed
// as the current DHT reading algorithm adjusts itself to work on faster procs.
DHT dht(DHTPIN, DHTTYPE);

void setup() {
  Serial.begin(9600);
  Serial.println("DHTxx test!");

  dht.begin();
}

void loop() {
  // Wait a few seconds between measurements.
  delay(2000);

  // Reading temperature or humidity takes about 250 milliseconds!
  // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
  float h = dht.readHumidity();
  // Read temperature as Celsius (the default)
  float t = dht.readTemperature();
  // Read temperature as Fahrenheit (isFahrenheit = true)
  float f = dht.readTemperature(true);

  // Check if any reads failed and exit early (to try again).
  if (isnan(h) || isnan(t) || isnan(f)) {
    Serial.println("Failed to read from DHT sensor!");
    return;
  }

  // Compute heat index in Fahrenheit (the default)
  float hif = dht.computeHeatIndex(f, h);
  // Compute heat index in Celsius (isFahreheit = false)
  float hic = dht.computeHeatIndex(t, h, false);

  Serial.print("Humidity: ");
  Serial.print(h);
  Serial.print(" %\t");
  Serial.print("Temperature: ");
  Serial.print(t);
  Serial.print(" *C ");
  Serial.print(f);
  Serial.print(" *F\t");
  Serial.print("Heat index: ");
  Serial.print(hic);
  Serial.print(" *C ");
  Serial.print(hif);
  Serial.println(" *F");
}

 


搜尋